21

Hi Steph, I live in Tower Hamlets (E3), London. I went to a hackspace but there was just a guy giving some basic classes and selling his 3d printer.

Cheers

Iñigo

1 Like
22

Yes you are right, that’s the best way of learning but with so many sensible parts made by plastic is quite scary to manipulate :wink:

Sometimes helps to learn from people who knows more :slight_smile:

23

Yes, I know that place, last month I went there in the 3d printer event but it was a very small group.

24

Hi Iñigo,

Thank you for your answer. I wish I could be there to help you but for sure we can meet when you come to Lisbon. I would be glad to show some of my works.

Hope you can find someone near you to help you.

Best wishes,

Tiago Figueiredo

25

I’m in the U.S.but wanted to welcome you to the 3d printing community. great minds and good people. good luck and happy you are joining the fun. Scott

26

Well I want to ask something please

to print something on a 3d printer it has have thickness

we have to print 8 units on a 3d printer … something we have done before in grasshopper

and i want to connect the one unit with the other

27

Hey there @Renos_Evangelak. Think it would be useful for you to start a separate thread to discuss this issue.

Cheers!

AndyL

Pot8oSh3D

28

Hey @l33kox. Why don’t you stop by at the 3D Print Show, London, the week after next. Come along to the 3DHubs stand and I’m sure you’ll find someone to give you some good advice. If I’m not there, wander over to the Sketchfab stand. I may be there and I’d be happy to point you in the right direction.

Cheers,

AndyL

Pot8oSh3D

29

To get the fan to work, so long as you are sure of the wiring, try sending an M106 command. i.e, M106 S128 (this will run the fan at 50%).

If you could send a picture of the wiring to your mainboard, that would help a lot. Looking at the BCN3D+ website, the fan is there to cool the all-metal hotend, so it should be wired directly to the 12volt supply, as you want cooling on the hotend constantly, regardless of flow-rate, etc.

By ‘z-axis not moving symmetrically’ do you mean they aren’t moving by the same amount, or do you mean they are wobbling?

30

Many thanks Scott, I really like this community full of great people. For the moment I have to learn a lot but I hope in the future to be helpfull. good luck for you too. Iñigo

31

Hi AndyL, I saw the meeting and I wanted to go but that week I have a weeding in my country so I am not able to go but I will be in the next meeting and hope with the printer running :slight_smile: Many thanks. Iñigo

32

Hi, many thanks for the tips, I appreciate a lot. About the current status, I did some progressions and even I started to print small things but I have to stop because I have to solve these two problems.

The z-axis with problems is the one with the engine, and sometimes start to make a noise and go slower until get like stuck. I don’t know the reason, maybe no enough power or probably I did something bad. And the fan still it’s no working.

Anyways you already help me a lot and this forum motived me so much!! Tomorrow I will try the command and I will upload the photo.

Many thanks

Iñigo

33

Inigo,

Just to be clear, the MeetUp is the evening of Wednesday 20th. The show runs from Thursday 21st to Saturday 23rd.

Hope you enjoy the wedding.

Cheers,

AndyL

34

Hello Iñigo,
I am a master student in Brunel University. My major is product design. I am doing the survey about the 3D printing for my dissertation. I really need your help to finish the questionnaire, it just has 9 questions that will take you few minutes.

Questionnaire:
https://www.surveymonkey.com/s/562XJHP

Your feedback is very important.
Thank you for participating in my survey.

Rina