1

I’ve solved my filament sourcing issues and will be purchasing by the case (10 rolls) now. I need to make some room for the first shipment and sell off or throw away some unopened and some used filament.

  • Hatchbox Transparent ABS
    • Unopened Blue - $22
    • Unopened Yellow - $22
    • Opened and Resealed Red - $15
  • ProtoType Supply Blue HIPS + Blue ABS Unopened - $30 (set)
  • Esun 3.0mm Silver PLA Unopened $15
  • Esun Green PLA Unopened - $15
  • Esun open silver, black, red, orange (Not vacuum sealed) $10 for the lot.
  • SOLD: Octave - Taulman 3D 618 Nylon 1lb unused spool - $10.

Or all of it and 4-5 almost empty rolls of hatchbox abs and pla for $100.

If anyone local wants hatchbox filament I can add your spools to my order just let me know it’s a little bit cheaper than amazon and megalowmart.

IMG_20160517_012502.jpg
IMG_20160517_012502.jpg651×1024 195 KB
IMG_20160517_012458.jpg
IMG_20160517_012458.jpg681×1024 228 KB
IMG_20160517_012452.jpg
IMG_20160517_012452.jpg478×1024 148 KB
IMG_20160517_012448.jpg
IMG_20160517_012448.jpg466×1024 129 KB
IMG_20160517_012441.jpg
IMG_20160517_012441.jpg817×1024 287 KB
IMG_20160517_012431.jpg
IMG_20160517_012431.jpg815×1024 267 KB
IMG_20160517_012424.jpg
IMG_20160517_012424.jpg822×1024 272 KB
IMG_20160517_012415.jpg
IMG_20160517_012415.jpg855×1024 325 KB
IMG_20160517_012405.jpg
IMG_20160517_012405.jpg981×1024 301 KB
IMG_20160517_012358.jpg
IMG_20160517_012358.jpg1280×860 275 KB
IMG_20160517_012352.jpg
IMG_20160517_012352.jpg1280×875 332 KB
IMG_20160517_012347.jpg
IMG_20160517_012347.jpg1280×878 375 KB
IMG_20160517_012308.jpg
IMG_20160517_012308.jpg440×1024 175 KB
IMG_20160517_012250.jpg
IMG_20160517_012250.jpg1280×975 367 KB

2

I’ll take the Nylon. I’d like to give nylon a try for once. Do you have any means of drying it?

3

I have an oven and a vacuum chamber. I don’t have a heated vacuum chamber or a vacuum oven though.

4

If you like you can post them on a marketplace I made for 3Dprinters and accessoires.

I’m generating as much traffic as I can.

I made this website because we all have spare parts or filament we doen’t use (anymore) we did create a website where we can easily get rid of those leftovers.

http://reused3dprinters.com

Also if you know places, websites, blogs where I could make promotion or an artikel about the site, please let me know.

its in everybody’s intrest to make the website a succes, for the sellers to get as much traffic by there ads. and for buyers to get an as wide variety of advertisements as possible

1 Like
5

I can bake it at 180f for 6 hours and then vacuum seal it at 20hg? with dessicant.

6

OK. Send me an email at 17.markyoe@gmail.com

7

I wasn’t kidding about throwing this all in the trash. I have 40+ spools en route and need space. Make an offer. I’ll keep the hatchbox as it’ll get used eventually.